Kradal Flooring polyurethane cleaner

posted 23 May 2013, 01:56 by Paul Davey   [ updated 28 May 2013, 02:17 by Site Administrator ]

PU-Cleaner
PU-cleaning-fluid
Product Description:
 Ideal cleaner for use after installing and for maintaining factory-cured floor coverings. Removes dirt, fat, grease and shoe marks. Does not leave a residue. 750ml Bottle

Areas of Application: Ideal cleaner for use after installing and for maintaining KRADAL Flooring and factory cured floor coverings made of PVC, CV, rubber, and polyolefin.

Method of Application: 
Cleaning after installation: Remove coarse dirt using a brush or vacuum cleaner. In case of stubborn dirt, dilute PU Cleaner in a ratio of 1:10 (1 litre to 10 litres of water), reducing the concentration accordingly for slight soiling. Distribute the cleaning solution over the floor and, after allowing to stand for a short time, treat the floor surface using a scrubbing brush. Where larger areas are involved, the Monodisc should be used with red pad or scrubbing brush. Take up the dirt using a wide-headed absorbent wiper mop, for larger floor areas using a Spray Extractor machine with hard floor adapter. Wipe over with clear water to neutralise. 
Consumption: approx. 1 l = 50- 100 m²

Daily Cleaning: Dilute PU Cleaner in a ratio of 1:200 (50 ml to 10 litres of water) and wipe over the floor using this solution. The concentration can be reduced to 1:400 (25 ml to 10 litres of water) when using a fully automatic cleaning appliance. 
Consumption: 1 l = 1000 m²

Notes: 
1) Sensitive surfaces (such as wood, metal, furnishings) should not be sprayed with the cleaning solution.

Usually ships in: 14 days



Kradal Flooring stain remover

posted 23 May 2013, 01:32 by Paul Davey   [ updated 28 May 2013, 02:19 by Site Administrator ]

Elatex Stain Remover
Elatex stain remover
Areas of Application:
Resilient floors (vinyl, linoleum and rubber), laminates, sealed wood and cork floors, as well as carpets and upholstery.

For floors without a polish or sealer spray Elatex directly onto the soiled area. Leave to react for a short time, treat residues with a cloth or non-abrasive white pad. Finally wipe with clear water. Avoid long-lasting action on polymer-coated floors as well as sensitive surfaces (e.g. sealed wood and cork floors). In such cases spray Elatex onto a cloth and take up loosened stains carefully. Thereafter treat with the floor with a suitable care agent.

200 ml bottle with atomiser

Usually ships in: 7 days



Kradal Flooring polyurethane sealer

posted 23 May 2013, 01:05 by Paul Davey   [ updated 28 May 2013, 02:22 by Site Administrator ]

PU Sealer Anti-slip
PU_Slip_and_sealer
Product Description:
 5.0 ltrs. A special 2 part polyurethane-based sealer for the long-term protection of floorings in areas with particular requirements for slip-prevention. The product forms an extremely hard-wearin sealeant film of outstanding durability. Special anti-slip additive increases slip-reduction, enabling the sealant film to be classified in evaluation group R10. Slip-reduction effect tested an approved by the employer’s liability insurance association for work safety (Berufsgenossenschaftliches Institut für Arbeitsschutz-BGIA-) in accordance with the regulation given in BGR 181 and DIN 51130.

Areas of Application: PVC, linoleum and rubber floorings with a plain or slightly structured surface, including qualities with a polyurethane factory finish. Not suitable for conductive floorings.

Method of Application:  Prior to application, the floor must be thoroughly mechanically cleaned with a green or silver pad using the procedures laid down for newly laid floors or for basic cleaning operations. The floor surface must be clean and dry, free from dust, grease, oil, wax and care product residues. In the case of linoleum and other floor qualities with a removable factory protective finish, this must be removed completely.

First pour the contents of the Anti-slip additive package (330 g) into the PU sealer mat canister and carefully mix by thorough shaking. Optimal mixing is achieved by using a boring tool with mixer and sealer bucket. After mixing, add cross-linker (0.5 litre) to sealer and carefully mix both components. Room and working temperature: 15-25°C.

Roll out the mixed sealer evenly over the floor using the „Aquatop“ roller (10 mm). Commence work on the side with the main incidence of light (as a rule this is the side of the room where there is a window) and work away from the light source. In this way it will be possible to keep an eye on the floor during work and immediately correct any problems as they arise. Apply the sealer and distribute with the roller, working in sections of a maximum of 1 metre in width at right angles to the incidence of light (i.e., parallel to the window wall) and then roll it out evenly towards the light. Avoid the formation of pools. Unused sealer mix should occasionally be homogenised by shaking or stirring.
After allowing sufficient time for drying (minimum of 2 hours, however on the same day), apply a second coat of PU sealer mat, however without adding the Anti-slip additive.

The floor can be walked on if caution is used 24 hours after the application of the final sealer coating. The protective film reaches its final level of hardness after approx. 7 days at room temperature.

Notes:  
1)    Once mixed, the mixture of PU Sealer mat, cross-linker and additive is suitable for use for approx. 4 hours at the prescribed working temperature of 15-25°C. For this reason, only mix the quantity of sealer that can be processed within this period of time. Where sealer and cross-linker are subjected to higher temperatures, the working time is reduced considerably. In case of cold components, the mixing procedure cannot be performed with sufficient thoroughness. Do not tightly seal the canister containing ready-mixed sealer since the sealer/cross-linker mixture can, in the course of time react even in the canister resulting in the build-up of reactive gases.

2)    Ensure that there is sufficient ventilation but avoid exposure to drafts and strong sunlight during application and drying processes and protect the surface from dust. Turn off under-floor central heating in good time prior to us.

3)    For surfaces with non-removable factory-applied polyurethane treatment which are fully clean and without residue, priming of the surface with a PU silver pad to remove gloss will suffice instead of thorough cleaning, before application of sealer compound.

Consumption: 50 g = 1 m² per application

Attention: Intensively coloured products (hair colorants, coloured wound disinfectants, etc.) and plasticizer migrations (e.g., of rubber) can lead to irreversible discoloration in the sealant film, severe mechanical damage to an acceleration in wear. Evidence of abrasion may necessitate partial or full-area repair of the the sealer film.
Availability

Usually ships in: 7 days



1-3 of 3